Our products
Product categories
Working pressure [bar]
Minimum operating temperature [Ā°C]
Maximum operating temperature [Ā°C]
Material
Vacuum resistance
Standard length [m]
Select options This product has multiple variants. The options may be chosen on the product page / Details90Ā° angled plug connector with hose plug connections for inch diameter hoses, series S, type PULC. An economical solution for connecting flexible pneumatic hoses with an inch calibrated outer diameter. Easy and quick to use. Material: plastic. Working pressure: 10 bar. Vacuum: 0.99 bar. Operating temperature: from 0Ā°C to +60Ā°C. Sealing: NBR.- Select options This product has multiple variants. The options may be chosen on the product page / DetailsAdaptor - high-pressure plug with external BSP thread (60Ā° cone seal), type A113. Material: carbon steel, galvanized.
- Available on requestAdapter with external BSP thread (seal on internal cone 60Ā°) and external BSPT thread (seal on external cone 120Ā°) allowing the connection of quick couplings and UHP hoses to each other, as well as connecting them to UHP connection blocks. Material: black galvanized steel. Working pressure: 2500 bar.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsThe FIL NEW DEAL series filter is recommended for decentralized compressed air systems or in close proximity to actuating devices. Due to its construction (metal structure), it is characterized by resistance to harsh working conditions. Designed for use at higher pressures. Size: 1/4", 3/8", 1/2", 3/4", 1". Filtration degree: 4 Āµm, 20 Āµm, 50 Āµm. Supply pressure: up to 18 bar, for drain RA up to 10 bar. Operating temperature: up to +50Ā°C. Connection: BSP female thread 1/4", 3/8", 1/2", 3/4", 1". Condensate drain: manual / semi-automatic (RMSA), automatic (SAC). Flow rate: 1700 l/min - 1/4", 4100 l/min - 3/8", 1/2", 11000 l/min - 3/4", 1" (at an inlet pressure of 6 bar Īp = 1 bar).
- Available on requestDismantling key used for disconnecting hoses from plug-in hoses. Designed for series R and RL (FOX). Outer diameter of the hose from 3 to 10 mm.
- Select options This product has multiple variants. The options may be chosen on the product page / Details90Ā° elbow (R = 1.5 x d) KSBB 45 designed for quick and efficient installation of suction hoses using BC screw bridge clamps. Material: galvanized steel.
- Available on requestBANJO crimping end for Teflon brake hoses. Material: carbon steel, chrome-plated.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsSpare blade for scissors PZP12 (ZC-PZP12).
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsHydraulic pump MPT100 with manual drive intended for the crimping tool for air conditioning type TNT250/B. Height: 315 mm.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsAF-THU clamping sleeve for HYPERLINE SB, FX, V type PTFE hoses. Diameter D1 [mm] - outer diameter. Diameter D2 [mm] - inner diameter. Diameter D3 [mm] - lock diameter. Material: AISI 304 steel.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsFlat gasket IBC for flange PN made according to standard PN-EN 1514-1. The permissible working pressure at which a given gasket can be used depends on the temperature and type of medium (selection should be agreed with TUBES INTERNATIONALĀ®). When selecting a gasket, attention should be paid to the outer diameter dimension, appropriate for the flange class. For example: gasket DN 10 PN40 is suitable for classes PN10, PN16, and PN25. Material: EPDM. Working pressure: up to 60 bar. Operating temperature: from -30Ā°C to +120Ā°C.
- Available on requestLightweight, flexible hose designed for the removal of dust, wood shavings, chips, and lightweight abrasive bulk materials. Used in the woodworking, construction, and food industries. Ozone resistant. Wall thickness is measured between the spiral. Other diameters available in the range of 30 Ć· 400 mm. Hose material: transparent polyurethane. Reinforcement: copper-plated steel wire spiral. Operating temperature: from -40Ā°C to +90Ā°C.
- Available on request
Suction and delivery hose for sand, chips, fiberglass ABRATECH SD SFĀ®
All products | Bulk material transfer hosesFrom: 2 688 kr / m / pcs
Available on orderSuction and pressure hose for pneumatic transport of dry abrasive substances. Thick inner layer made of polyurethane, with very high abrasion resistance (below 36 mmĀ³ according to DIN 53516), very smooth and with a low friction coefficient, allowing the conveyed product to slide. Two built-in copper wires that, when grounded (connected to a grounded end), discharge electric charges. The outer layer is corrugated, made of black, antistatic (R<10^6Ī©) SBR/NR rubber resistant to abrasion, ozone, and aging. The hose is designed for the transport of dry, highly abrasive substances, particularly in foundries, welding shops, the ceramic industry, construction, and woodworking. Installation: The hose is intended for installation using the GHIBLI system - aluminum half-flanges PN10 applied externally to the hose. Inner layer: special polyurethane (PU). Reinforcement: synthetic cord, steel spiral. Outer layer: black SBR/NR rubber. Working pressure: from 3 bar to 10 bar - depending on the hose diameter. Vacuum: 0.9 bar. Operating temperature: from -30Ā°C to +80Ā°C (temporarily up to +100Ā°C). - Select options This product has multiple variants. The options may be chosen on the product page / DetailsLightweight, flexible hose designed for solvents, paints, isocyanates, polyols, gases, air, and water-based fluids. Inner layer: polyamide. Reinforcement: aramid braid + steel braid. Outer layer: microperforated polyurethane. Operating temperature: from -40Ā°C to +93Ā°C (for water and air up to +65Ā°C).
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsEnd cap for CAMLOCK DP coupling made according to American military standard MIL-C-27487 (A-A-59326). Working pressure: up to 7 bar, depending on coupling size. Material: polypropylene reinforced with fiberglass.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsSTORZ blind cap, equipped with a chain to prevent loss, intended for transmission installations for liquid and bulk substances. Used in firefighting, irrigation systems, chemical industry, food industry, agriculture, etc. With a symmetrical design of the connection part, it easily connects with each other. Elements with the same coupling spacing can be connected. Material: stainless steel. Working pressure: 16 bar. Seal: viton.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsSimple foot valve with protective cover and sockets in the front plane, used for foot control by the operator of devices in pneumatic systems. Connection: 1/4". Working pressure: from 2.5 bar to 10 bar. Operating temperature: -10Ā°C to +60Ā°C. Nominal flow: 840 l/min (at inlet pressure 6 bar Īp = 1 bar).
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsStraight bulkhead fitting JIC 37Ā° with external UNF thread (seal on external 37Ā° cone). Material: AISI 316 steel.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsLET-LOKĀ® type tee fitting for metric tubing intended mainly for the chemical, petrochemical, pharmaceutical, energy, nuclear power, and process engineering industries. The allowable working pressure is determined based on the outer diameter and wall thickness of the tubing (details in the attachment). Material: AISI 316 steel.
- Select options This product has multiple variants. The options may be chosen on the product page / Details90Ā° high-pressure adapter type A114C with external BSP thread (60Ā° cone sealing) and internal BSP thread, with swivel nut (60Ā° cone sealing), "compact" version. Material: AISI 316L steel.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsScrewed end with internal thread, type FACR, for Teflon brake hoses. Material: carbon steel, chrome-plated.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsBanjo elbow body, type R28, for screws of series D, intended for connections of pipes and other components in pneumatic systems. Easy and quick to use for multiple assemblies without loss of sealing on the mechanical and pneumatic side. Material: plastic. Working pressure: 12 bar. Working medium: vacuum, air. Operating temperature: from -20Ā°C to +60Ā°C. Sealing: NBR.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsMetric tube fitting type LET-LOKĀ® with external BSP thread intended mainly for the chemical, petrochemical, pharmaceutical, energy, nuclear power, and process engineering industries. The allowable working pressure is determined based on the outer diameter and wall thickness of the tube (details in the attachment). Material: AISI 316 steel.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsT-type block tee with internal thread enabling the connection of quick couplings and UHP hoses. Material: carbon steel, black galvanized. Working pressure: 700 bar (with a safety factor of 4), 1000 bar (with a safety factor of 2.8).
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsSymmetrical "Y" tee KTSBY designed for quick and efficient installation of suction hoses using BC screw bridge clamps. Material: galvanized steel.
- Available on requestLightweight, highly flexible and pliable, chemically resistant hose designed for the discharge of aggressive chemical vapors, gases, dust, and fibers. Mainly used in the chemical industry and, among others, in asbestos removal. Very good chemical resistance to solvents and other aggressive vapors. Resistant to hydrolysis and biological corrosion. Free from halogen compounds and plasticizers. Characterized by high compressibility - up to 1:8, strong construction, and impact resistance due to the external spiral. Also available with a stainless steel spiral (from a diameter of 80 mm). Hose installation on couplings with bridge clamps (left-handed). Chemical resistance verification - chemical resistance table for polyethylene (preliminary selection), confirmation of resistance and application conditions - by Tubes International. Standard length: from 2 to 10 m. Hose material: polyethylene fabric coated with polyethylene (PE). Reinforcement: external spiral made of galvanized steel wire and sheet. Operating temperature: from -40Ā°C to +80Ā°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsLightweight, flexible hose designed for hydraulic oil installations, gases, air, fuels, water-based fluids. Resistant to very low temperatures and harsh weather conditions. Standards: SAE 100R18, ISO 3949-R18. Inner layer: polyester. Reinforcement: one or two synthetic braids. Outer layer: micro-perforated polyurethane. Working pressure: 210 bar. Operating temperature: from -55Ā°C to +100Ā°C (for water and air up to +70Ā°C).
- Available on request
Delivery hose for transfer of coal, coke, steel shot, glass shards ALUSPHEREĀ®
All products | Bulk material transfer hosesFrom: 2 382 kr / m / pcs
Available on orderPressure hose for pneumatic transport of dry abrasive substances. Special hose design with exceptional abrasion resistance. The inner layer is smooth, made of black antistatic natural rubber with embedded alumina (Al2O3) ceramic beads, a material with high hardness. Built-in copper wire that, when grounded (connected to a grounded end), dissipates electric charges. The outer layer is made of black antistatic (R<106Ī©) SBR/NR rubber resistant to abrasion and aging. The hose is intended for the transport of dry highly abrasive substances: e.g., dry cement, coal, coal dust, coke, solid fuels from secondary raw materials, minerals, ceramic powders, steel shot, glass shards, fiberglass. Used in steel mills, coking plants, power plants, cement plants, mines, glassworks, abrasive material factories, and insulation material factories. The advantage is the long lifespan of the hose in these applications ā a traditional abrasion-resistant rubber hose may last only a few days, while the ALUSPHERE hose can last several months under the same conditions. Inner layer: ceramic beads embedded in black NR rubber. Reinforcement: synthetic cord. Outer layer: black SBR/NR rubber. Working pressure: 12 bar. Operating temperature: from -30Ā°C to +80Ā°C. - Select options This product has multiple variants. The options may be chosen on the product page / DetailsCAMLOCK AR (reduction) connector plug with internal BSP thread made according to the American military standard MIL-C-27487 (A-A-59326), commonly used as a transfer connection, particularly in the petrochemical industry. Working pressure: up to 10 bar. Material: aluminum.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsREG pressure reducing valve, SYNTESIĀ® series, with end connections 1/8" to 1", is used for regulating operating pressure and maintaining it at a constant level, ensuring proper operation in the connected installation, regardless of the changing consumption of the medium. The valve uses a shaped diaphragm instead of a flat diaphragm, which provides higher nominal flow values due to greater diaphragm travel, as well as increased sensitivity and response speed to setting changes by reducing static and kinetic friction of components and greater accuracy in maintaining the set output pressure with changes in flow and supply pressure. In the event of an increase in output pressure above the set value, the diaphragm opens the drain valve and vents the reducer until the pressure value matches the setting. The push-lock mechanism allows the knob to be locked in any position by pressing it. The locking plate enables the installation of a padlock to prevent unauthorized changes to the output pressure setting. Additional connections at the front and back can be used to connect a pressure gauge, pneumatic-electric relay, or plug couplings. Air drawn from these connections is reduced. Size: SY1, SY2. Output pressure range: 0 to 2, 0 to 4, 0 to 8, 0 to 12 bar. Supply pressure: up to 15 bar, depending on size. Operating temperature: from -10Ā°C to +50Ā°C. Connection: BSP thread 1/8" to 1". Additional connection for pressure gauge or couplings: BSP thread 1/8" for size SY1, BSP thread 1/4" for size SY2. Flow: 1200 l/min - 1/8", 2800 l/min - 1/4", 3350 l/min - 3/8" (SY1), 5300 l/min - 3/8" (SY2), 7400 l/min - 1/2", 7600 l/min - 3/4" and 1" (at an inlet pressure of 6 bar Īp = 1 bar).
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsFlange connection set (EN 1092), type SZ1. Included: DIN931 screws - 4 pieces, DIN934 nuts - 4 pieces, and DIN125A washers - 4 pieces. Mechanical property class: A2-70 - screws; A2-70 - nuts. Selection of screws and nuts for flanges according to the table in the appendix. Material: AISI 304 steel.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsAdaptor - high-pressure tee type A109 with external thread 3 x BSP (seal cone 60Ā°). Material: carbon steel, galvanized.
- Available on requestAdapter with external BSP thread (sealing on external cone 120Ā°) and external BSP thread (sealing on external cone 120Ā°) allowing the connection of quick couplings and UHP hoses to each other, as well as connecting them to UHP connection blocks. Material: black galvanized steel. Working pressure: 3000 bar.
- Available on request
Compressed air filter with reducer (filterreducer) FR 300, with FRL connection, SKILLAIRĀ® series
Air preparation elements (FRL) | All productsFrom: 1 365 kr / m / pcs
Available on orderFilter with pressure regulator (filter regulator) FR, SKILLAIRĀ® series, is a device consisting of a filter and a pressure reducing valve. It reduces and purifies the air supplied by the compressor. Size: 300. Output pressure range: 0Ć·2, 0Ć·4, 0Ć·8, 0Ć·12 bar. Supply pressure: up to 13 bar, depending on the type of discharge. Operating temperature: up to +50Ā°C. Connection: BSP 1/2" to 1". Pressure gauge connection: BSP 1/8". Condensate discharge: manual / semi-automatic (RMSA), automatic (RA, SAC). Flow rate: 5600 l/min at an inlet pressure of 6 bar Īp = 1 bar). - Select options This product has multiple variants. The options may be chosen on the product page / DetailsDouble socket CAMLOCK DD connector made according to the American military standard MIL-C-27487 (A-A-59326). Commonly used as a transfer connector, particularly in the petrochemical industry. Working pressure: up to 10 bar, depending on the size of the connector. Material: aluminum. Levers: AISI 304 steel (in sizes 1.1/4" to 4" - levers made of brass). Sealing: NBR.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsComplete BANJO plug tee, double, type R57, intended for connecting hoses and other components in pneumatic systems. Easy and quick to use for multiple assemblies without loss of sealing on the mechanical and pneumatic sides. Material: nickel-plated brass. Working pressure: 16 bar. Working medium: vacuum, air. Operating temperature: from -20Ā°C to +80Ā°C. Sealing: NBR.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsStraight crimped tube end, type EP, for Teflon brake hoses. Material: carbon steel, chrome-plated.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsFlat gasket IBC for ASA flange made according to ASME B16.21 (ANSI) standards. The permissible working pressure at which a given gasket can be used depends on the temperature and type of medium (selection should be agreed with TUBES INTERNATIONALĀ®). When selecting a gasket, attention should be paid to the outer diameter dimension, appropriate for the flange class. For example: gasket DN 15 ASA600 is suitable for ASA300 and ASA400 classes. Material: KLINGER SIL 4430. Working pressure: up to 100 bar. Operating temperature: from -200Ā°C to +400Ā°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsVery lightweight and extremely flexible rubber hose for dust extraction, powders, and other lightly abrasive materials. The inner layer is smooth, made of wear-resistant rubber with a thickness of 2.4 mm. The outer layer is corrugated, resistant to abrasion and weather conditions. Thanks to the steel spiral reinforcement, it is resistant to kinking and vacuum up to 0.6 bar. Not intended for use with positive pressure, designed only for vacuum (extraction). Due to its lightness and exceptional flexibility for a rubber hose, it performs excellently in vacuum cleaning systems in the industry, such as in quarries or foundries. It features a copper anti-static wire for discharging electric charges. Inner layer: black natural rubber. Reinforcement: synthetic cord, steel spiral. Outer layer: black SBR rubber. Vacuum: up to 0.6 bar. Operating temperature: from -40Ā°C to +70Ā°C.
- Available on requestPolyurethane hose, reinforced with a steel wire spiral, designed for the discharge and transport of bulk materials, powders, and sawdust. Ozone resistant. Hose material: transparent polyurethane. Reinforcement: galvanized steel wire spiral. Operating temperature: from -40Ā°C to +90Ā°C.
