Our products
Product categories
Working pressure [bar]
Minimum operating temperature [°C]
Maximum operating temperature [°C]
Material
Vacuum resistance
Standard length [m]
- Available on requestLightweight, highly durable, universal high-quality flat hose used in the mining, oil, energy, and agriculture industries. Particularly used for water, sludge, wastewater, and fertilizers. Made from hydrolysis and microbe-resistant polyurethane - polyether. Reinforced with circumferentially woven polyester braid bonded and surrounded by polyurethane in the original hot thermoplastic polyurethane extrusion production process through braiding. The hose has high tensile strength, with minimal elongation under pressure (up to 2%) and no tendency to kink or twist. Due to its durability combined with ease of handling (unrolling, laying, storing), it is widely used in water systems (drainage of open-pit mines, water supply, drainage, and wastewater discharge) and beyond. Resistant to a wide range of chemicals, microbes, fungi, hydrolysis, weather conditions, UV, and ozone. Good abrasion resistance. Available on special order in lengths longer than 200 meters in diameters up to 6”. To confirm the resistance and application conditions of the hose, contact Tubes International. Maximum working pressure for temporary use established according to a safety factor of 2:1 approved by the manufacturer (only for water and safe, non-flammable liquids). For maximum longevity, it is not recommended to exceed 1/3 of the bursting pressure. Standard roll length: 200 m. Hose material: black polyurethane - polyether (PU). Working pressure: from 8 bar to 27 bar - depending on hose diameter and temperature. Operating temperature: from -50°C to +75°C (water).
- Available on requestHigh-pressure, highly durable hose for compressed air transmission. Designed for use in harsh conditions such as construction sites, mines, etc., to power equipment with high compressed air consumption. Extremely robust and durable due to high-quality materials and a double-layer construction – double reinforcement with circumferentially woven high-strength polyester braid, completely covered and lined with thermoplastic polyurethane (PU). The hose has very good abrasion resistance, is puncture-resistant, tear-resistant, and oil-resistant. The hose does not elongate under pressure and is resistant to longitudinal loads. Flat in a resting state, which facilitates handling and storage. Available as ready-made hoses of 20 or 40 m in length, with factory-installed fittings. Use for high-pressure air should always be preceded by a risk analysis in case of accidental disconnection or rupture of the hose and potential application of safeguards. The maximum working pressure of the hose is established according to a safety factor of 4:1 approved by the manufacturer for air. Exceeding 1/3 of the specified breaking force is not recommended. Hose material: polyurethane (PU). Reinforcement: double polyester braid. Outer layer: orange polyurethane (PU). Working pressure: from 30 bar to 43.75 bar - depending on the hose diameter. Operating temperature: from -50°C to +110°C.
- Available on requestStrong, specialized drag hose for farmers designed for natural fertilization in crop production (manure and slurry fertilization). Used in comprehensive slurry spreading systems, including spreaders. In these solutions, the slurry is pumped using a hose from the tank to dispensers/tanks mounted on the tractor and then spread directly onto the soil surface. Extremely durable and long-lasting due to high-quality materials and construction. Reinforced with a circumferentially woven high-strength polyester braid bonded and surrounded by polyurethane in the original hot thermoplastic polyurethane extrusion process through braiding. Due to its high resistance to tensile stress, abrasion, punctures, weather conditions, UV radiation, and small bend radius, it is widely used for field fertilization. Also available in other versions: DRAGMAN EXTRA (with increased breaking strength), DRAGMAN PREMIUM (with increased abrasion resistance), and in longer lengths. Maximum working pressure for temporary use established according to a safety factor of 2:1 approved by the manufacturer (only for water and safe, non-flammable liquids). For maximum longevity, it is not recommended to exceed 1/3 of the bursting pressure and the specified breaking strength. Standard roll length: 200 m. Hose material: orange polyurethane (PU) pressed into high-strength polyester braid during hose extrusion. Working pressure: from 15 bar to 22.5 bar - depending on hose diameter and temperature. Operating temperature: from -50°C to +65°C.
Select options This product has multiple variants. The options may be chosen on the product page / DetailsStrong pressure hose designed for the transmission of water or compressed air. Used in construction (particularly in demolition companies), industry, and mining. Suitable for heavy-duty applications. The yellow color ensures excellent visibility of the hose. The inner layer is smooth, providing minimal flow loss. The outer layer is slightly longitudinally ribbed, which increases abrasion resistance and protects against contact with hot elements. Resistant to abrasion, ozone, weather conditions, oil, fuels, and a wide range of chemicals. Lighter and more flexible than standard rubber hoses. Flat when at rest, facilitating handling and storage. Does not require washing and drying. Resistant to longitudinal loads – during unwinding and pulling (the longitudinal force should never exceed 1/3 of the specified breaking force, and the installation of fittings should consider the longitudinal force). Use for air should always be preceded by a risk analysis in case of accidental disconnection or rupture of the hose. Hose material: yellow NBR/PVC blend embedded in a polyester-polyamide braid during the hose extrusion process. Working pressure: 30 bar (water), 22 bar (air). Operating temperature: from -20°C to +80°C (water), from -20°C to +75°C (air).- Select options This product has multiple variants. The options may be chosen on the product page / DetailsStrong, flexible rubber fire hose, designed for use on reels. The ANKARA EN hose is manufactured according to the EN 694 standard, which is the European standard for hoses used in fixed fire protection installations and commonly used on reels in fixed hydrants in buildings, industrial installations, shopping centers, etc. The inner layer is made of EPDM rubber, resistant to light chemicals and fire-fighting foaming agents. The outer layer is made of EPDM rubber, resistant to abrasion and weather conditions. It performs excellently when mounted on reels, ensuring water flow even when the hose is not fully extended. The presented ANKARA hose is made according to the requirements of the older DIN 14817: 1991 standard, intended for powder and foam extinguishing agents, with an inner layer made of conductive NR/SBR rubber and a working pressure of up to 20 bar, also designed for use on reels. Inner layer: EPDM rubber (ANKARA EN), conductive NR/SBR rubber (ANKARA). Reinforcement: synthetic cord. Outer layer: EPDM rubber (ANKARA EN), SBR rubber (ANKARA). Working pressure: from 7 bar to 20 bar - depending on the size and type of hose. Operating temperature: from -20°C to +60°C (ANKARA EN), from -40°C to +70°C (ANKARA).
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsRectangular corrugated hose reinforced with a steel spiral, for hot water and antifreeze fluids, intended for automotive and industrial cooling systems. It has vacuum resistance. Inner layer resistant to heat and cooling fluids. Outer layer resistant to overheating, oil, and aging. Inner layer: black CR rubber. Reinforcement: synthetic cord, steel spiral. Outer layer: black CR rubber. Working pressure: up to 4 bar. Operating temperature: from -40°C to +100°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsStrong, flexible water hose designed for winding on reels. Intended for use in high-pressure firefighting equipment and fire trucks (booster hose). The inner layer is resistant to extinguishing agents and foaming agents. Reinforcement made of a thick layer of high-strength cord. The outer layer is weather-resistant. The CHICAGO EN hose differs from the basic version of the CHICAGO hose by being manufactured in accordance with standard EN 1947: 2014 (type C, class 1, category 2), while the CHICAGO EN GL is manufactured in accordance with EN 1947 but features a luminescent outer layer, allowing for easy visibility in darkness or smoke. Special versions of the hose compliant with standards ASTM C-542 and BS 3169 are also available upon request. Standard roll length: 60 m (120 m upon confirmation for the basic version of the hose). Inner layer: black EPDM rubber. Reinforcement: synthetic cord. Outer layer: black EPDM rubber (yellow luminescent synthetic rubber – GL version). Working pressure: 40 bar. Operating temperature: from -40°C to +100°C, from -20°C to +60°C (EN 1947).
- Available on requestCoolant hose in the system 3/4" made of corrosion-resistant acetal, resistant to solvents, oils, and greases, providing rigidity and elasticity of the hoses. Designed for low-pressure transmission of air, water, oils, and other substances used in cooling processes and metalworking. Resistant to abrasion and vibrations, ensuring 100% positional stability and does not cause damage to cutting tools. Very easy to expand modular construction. Available lengths: 2x145 mm, 100 mm, 200 mm, 300 mm, 400 mm, 500 mm, 600 mm, 700 mm, 800 mm, 900 mm, and 1000 mm. Material: acetal. Working pressure: up to 1.4 bar. Maximum flow: 5182 l/hour. Operating temperature: up to +76°C.
- Available on requestExtremely lightweight, flexible water delivery hose designed for internal fire protection of buildings. The inner layer is made of high-quality synthetic rubber. The outer layer consists of a strong, dense polyester braid reinforced with a thin, tightly wound PET spiral. The hose is used in internal hydrant cabinets with a length of 20 m to 30 m of hose wound on a drum (reel) with a nozzle mounted at the end of the hose. Compliant with EN 694 standard for fire hoses (type B class 5). In the field of fire protection (Poland), it has a CNBOP-PIB compliance certificate. It can also be used in industry - for seawater, industrial water, and some light diluted chemicals, as well as for air, dust, and light solid particles. It is not intended for use in harsh external conditions. Installation with clamps or crimping sleeves on ends with smooth, sharp-free fittings to avoid cutting the inner layer. Inner layer: smooth synthetic rubber. Reinforcement: polyester braid with a reinforcing spiral (thread) PET. Working pressure: from 7 bar to 12 bar - depending on the hose diameter. Operating temperature: from -20°C to +60°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsStrong, flexible, resistant to kinks suction and discharge hose designed for the transfer of hot, dry air from the compressor to the tank installation. Ideal for situations where a small bend radius is required. Used in road tankers for transporting bulk materials: cement trucks, feed trucks, etc., as well as in other industrial installations. The outer layer is resistant to ozone and weather conditions. Standard length: 60 m or 120 m. Inner layer: white EPR rubber. Reinforcement: synthetic braid, steel spiral. Outer layer: blue (SAHARA®LL BD) or black (SAHARA® LL BN/PRO) EPDM rubber. Working pressure: 10 bar. Operating temperature: from -40°C to +200°C (temporarily up to +240°C).
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsThick, strong, flexible, crush-resistant pressure hose designed for the transmission of hot, dry air from the compressor to the tank installation of the tanker. Used in road tankers for the transport of bulk materials: cement trucks, feed trucks, etc., as well as in other industrial installations. The outer layer is resistant to ozone and weather conditions. Standard length: 60 m or 120 m. Inner layer: white EPR rubber. Reinforcement: synthetic cord. Outer layer: blue EPDM rubber. Working pressure: 10 bar. Operating temperature: from -40°C to +200°C (temporarily up to +240°C).
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsLightweight, highly flexible compressed air hose with good resistance to mineral oils. Very abrasion-resistant. The yellow color ensures excellent visibility of the hose. The hose has a thickened outer layer every 20 m, marked on the hose ("TAGLIO / CUT"), and it is recommended to cut the hose and install fittings at these points. This reinforces the fitting installation area and makes it more resistant to bending. From a 60 m roll, three 20 m hoses with fittings can be made. However, it is also possible to use the hose with fittings installed in non-thickened areas. The hose is used for pneumatic hammers and drills. Inner layer: black PVC/NBR blend. Reinforcement: double polyester braid. Outer layer: black or yellow PVC/PU blend. Working pressure: 20 bar - dependent on temperature. Operating temperature: from -10°C to +60°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsFlexible hose with fittings intended for sanitary installations (hot and cold water). Widely used for connections in industrial systems, central heating, and air conditioning. Resistant to glycol concentrations up to 35%. Fittings made of brass, sleeves made of stainless steel (AISI 304). Has a hygiene certificate and technical approval for use in construction. Available with internal BSP thread on both ends and with internal and external BSP threads. Inner layer: black EPDM rubber (with enhanced parameters). Reinforcement: external braid made of AISI 304 steel. Working pressure: 16 bar. Operating temperature: up to +110°C.
- Available on requestCoolant hose in a 1/2" system made of corrosion-resistant acetal, resistant to solvents, oils, and greases, providing rigidity and flexibility of the hoses. Designed for low-pressure transmission of air, water, oils, and other substances used in cooling processes and metalworking. Resistant to abrasion and vibrations, ensuring 100% positional stability and does not cause damage to cutting tools. Very easy to expand modular construction. Available lengths: 2x140 mm, 100 mm, 200 mm, 300 mm, 400 mm, 500 mm, 600 mm, 700 mm, 800 mm, 900 mm, and 1000 mm. Material: acetal. Working pressure: up to 2 bar. Maximum flow: 2173 l/hour. Operating temperature: up to +76°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsHose intended for water and non-corrosive media. Used in sanitary installations, boilers, cooling systems. Two red stripes woven into the braid indicate the hose's resistance to elevated medium temperatures. Inner layer: non-toxic EPDM rubber. Reinforcement: braided galvanized steel. Working pressure: from 6 bar to 15 bar, depending on the hose diameter. Operating temperature: from -10°C to +110°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsCoolant hose in the 1/4" system made of corrosion-resistant acetal, resistant to solvents, oils, and greases, providing rigidity and flexibility of the hoses. Designed for low-pressure transmission of air, water, oils, and other substances used in cooling processes and metalworking. Resistant to abrasion and vibrations, ensuring 100% positional stability and does not cause damage to cutting tools. Very easy to expand modular construction. Available lengths: 2x14.5 cm or 100 cm. Material: acetal. Working pressure: up to 3 bar. Maximum flow: 900 l/hour. Operating temperature: up to +65°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsCoolant hose in a 1/2" system made of corrosion-resistant acetal, resistant to solvents, oils, and greases, providing rigidity and elasticity of the pipes. Designed for low-pressure transmission of air, water, oils, and other substances used in cooling processes and metalworking. Resistant to abrasion and vibrations, ensuring 100% positional stability and does not cause damage to cutting tools. Very easy to expand modular construction. Available lengths: 2x13.5 cm or 100 cm. Material: acetal. Working pressure: up to 2 bar. Maximum flow: 1700 l/hour. Operating temperature: up to +65°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsCoolant hose in the 3/8" system made of corrosion-resistant acetal, resistant to solvents, oils, and greases, providing rigidity and elasticity of the hoses. Designed for low-pressure transmission of air, water, oils, and other substances used in cooling processes and metalworking. Resistant to abrasion and vibrations, ensuring 100% positional stability and does not cause damage to cutting tools. Very easy to expand modular construction. Available lengths: 2x14.5 cm or 100 cm. Material: acetal. Working pressure: up to 3 bar. Maximum flow: 1500 l/hour. Operating temperature: up to +65°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsCoolant hose in the 1/4" system made of corrosion-resistant acetal, resistant to solvents, oils, and greases, providing rigidity and flexibility of the hoses. Designed for low-pressure transmission of air, water, oils, and other substances used in cooling processes and metalworking. Resistant to abrasion and vibrations, ensuring 100% positional stability and does not cause damage to cutting tools. Very easy to expand modular construction. Available lengths: 2x145 mm, 100 mm, 200 mm, 300 mm, 400 mm, 500 mm, 600 mm, 700 mm, 800 mm, 900 mm, and 1000 mm. Material: acetal. Working pressure: up to 3 bar. Maximum flow: 1136 l/hour. Operating temperature: up to +76°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsOil, grease, and hot chip resistant hose designed for low-pressure delivery of liquid or gaseous coolant during metal processing. It features a so-called shape memory, allowing for precise direction of the coolant flow. Supplied as ready-made hoses with an external BSP threaded connection ending with a metric external thread. Material: black PVC. Reinforcement: steel guiding cover, diameter DN 10 has an additional spiral cover made of nickel-plated steel sheet. Working pressure: 4 bar. Operating temperature: up to +80°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsHose with magnetic base and valve for coolant supply - system 1/4". Components: 20 segments (L=300 mm), flat nozzle 1", valve with external thread 1/4" BSPT, and magnetic base with "tail" for 1/4" hose (end thread size 1/8" NPT). Material: acetal. Working pressure: up to 3 bar. Operating temperature: up to +65°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsCoolant hose in a 3/4" system made of corrosion-resistant acetal, resistant to solvents, oils, and greases, providing rigidity and flexibility of the hoses. Designed for low-pressure transmission of air, water, oils, and other substances used in cooling processes and metalworking. Resistant to abrasion and vibrations, ensuring 100% positional stability and does not cause damage to cutting tools. Very easy to expand modular construction. Available lengths: 2x15 cm or 100 cm. Material: acetal. Working pressure: up to 1.4 bar. Maximum flow: 1900 l/hour. Operating temperature: up to +65°C.
- Select options This product has multiple variants. The options may be chosen on the product page / Details90° round nozzle for coolant hoses JETON - 1/4" system. Available in sizes 1/4", 3/8", and 1/2". Material: acetal. Working pressure: up to 2 bar. Operating temperature: up to +65°C.
- Select options This product has multiple variants. The options may be chosen on the product page / Details90° round nozzle for coolant hoses LOC-LINE® - 1/2" system. Available in sizes 1/4", 3/8", and 1/2". Material: acetal. Working pressure: up to 2 bar. Operating temperature: up to +76°C.
- Select options This product has multiple variants. The options may be chosen on the product page / Details90° round nozzle for coolant hoses JETON - 1/4" system. Available in sizes 1/16", 1/8", and 1/4". Material: acetal. Working pressure: up to 3 bar. Operating temperature: up to +65°C.
- Select options This product has multiple variants. The options may be chosen on the product page / Details90° round nozzle for coolant hoses LOC-LINE® - 1/4" system. Available in sizes 1/16", 1/8", and 1/4". Material: acetal. Working pressure: up to 3 bar. Operating temperature: up to +76°C.
- Available on requestFlat 90° nozzle with holes for coolant hoses JETON - 1/2" system. 8 holes with a diameter of 4.2 mm. Material: acetal. Working pressure: up to 2 bar. Operating temperature: up to +65°C.
- Select options This product has multiple variants. The options may be chosen on the product page / Details90° flat nozzle with holes for LOC-LINE® coolant hoses - 1/2" system. 8 holes with a diameter of 4.3 mm. Material: acetal. Working pressure: up to 2 bar. Operating temperature: up to +76°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsFlat 90° nozzle with holes for coolant hoses JETON - 1/4" system. 6 holes with a diameter of 2.3 mm. Material: acetal. Working pressure: up to 3 bar. Operating temperature: up to +65°C.
- Select options This product has multiple variants. The options may be chosen on the product page / Details90° flat nozzle with holes for LOC-LINE® coolant hoses - 1/4" system. 6 holes with a diameter of 2.5 mm. Material: acetal. Working pressure: up to 3 bar. Operating temperature: up to +76°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsSide nozzle for coolant JETON - 1/2" system. Enables the construction of, for example, a ring set. Material: acetal. Working pressure: up to 2 bar. Operating temperature: up to +65°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsSide nozzle for coolant JETON - 1/4" system. Enables the construction of, for example, a ring set. Material: acetal. Working pressure: up to 3 bar. Operating temperature: up to +65°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsSide nozzle for LOC-LINE® coolant - 1/4" system. Enables the construction of, for example, a ring set. Material: acetal. Working pressure: up to 3 bar. Operating temperature: up to +76°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsRound nozzle for coolant hoses JETON - 1/2" system. Available in sizes 1/4", 3/8", and 1/2". Material: acetal. Working pressure: up to 2 bar. Operating temperature: up to +65°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsRound nozzle for coolant hoses LOC-LINE® - 1/2" system. Available in sizes 1/4", 3/8", and 1/2". Material: acetal. Working pressure: up to 2 bar. Operating temperature: up to +76°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsRound nozzle for coolant hoses JETON - 1/4" system. Available in sizes 1/16", 1/8", and 1/4". Material: acetal. Working pressure: up to 3 bar. Operating temperature: up to +65°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsRound nozzle for coolant hoses LOC-LINE® - 1/4" system. Available in sizes 1/16", 1/8", and 1/4". Material: acetal. Working pressure: up to 3 bar. Operating temperature: up to +76°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsRound nozzle for coolant hoses JETON - 3/4" system. Available in sizes 5/8" and 3/4". Material: acetal. Working pressure: up to 1.4 bar. Operating temperature: up to +65°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsRound nozzle for coolant hoses LOC-LINE® - 3/4" system. Available in sizes 3/4" and 5/8". Material: acetal. Working pressure: up to 1.4 bar. Operating temperature: up to +76°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsRound nozzle for coolant hoses JETON - 3/8" system. Available in sizes 1/4", 3/8", and 1/2". Material: acetal. Working pressure: up to 3 bar. Operating temperature: up to +65°C.
